|
|
|
| User Opinions (1 vote) |
0%
100%
|
|
Thank you for rating this answer.
|
Power cycling your network should be attempted if you are experiencing any network connection issues between your Fyre Boxxx and the internet. Should the below steps not correct your network issue, the issue may lie in your router settings, click here.
Network Connection Issues
- Error 130
- Error 131
- Error 132
- "Unable to play content" error message
- Set-top box is unable to pull an IP address in the "network configuration" menu at the Enter Pin screen
- Test connection fails in the "network configuration" menu at the Enter Pin screen
Obtaining an IP address - Cable internet
The issue of a Fyre Boxxx not able to pull an IP address in the network configuration menu of the set-top box usually results from an Internet connection not able to be established. If you are not receiving an IP address or are receiving a 169.xxx.xxx.xx address then your FyreTV Boxxx is not configuring itself properly and communicating with the modem / router.
Proceed to the "ENTER Pin" screen on the Fyre Boxxx's User Interface > "network settings" > leave the "Automatic" (DHCP) checked > hit apply. If this option corrects the issue you will receive a "DCHP configuration has been set successfully" message. If this does not result in a "DCHP configuration has been set successfully" message proceed to the steps below.
1) Remove the power from the Cable modem and the router if present and leave everything unplugged.
2) Remove the Ethernet cable and power cord from the back of the Fyre Boxxx.
3) Plug in and power on the router if present and allow it to reconfigure itself. If no router is present, plug in and power on the Fyre Boxxx before proceeding to step 4.
4) Plug in the cable modem and allow it to reconfigure itself before accessing the Fyre Boxxx.
5) Proceed to the "network configuration" option on the Enter PIN screen > keep the "automatic (DHCP)" option checked > hit the "apply" button to reconfigure the network settings, if this option corrects the issue you will receive a "DCHP configuration has been set successfully" message. If this does not correct your issue proceed to the "Reconfiguring Your Network Settings - DSL / Cable" section below.
Note: Some modems have a recessed reset or reboot button that will need to be pushed in order to reset the modem configuration settings. The recessed button may not be able to be pushed with your finger and will require a paper clip or pin tip to push the button. If you have a network configuration of modem > box and your attempts to power cycle the network are still not resulting in the box pulling an IP address, you will need to look for the recessed button in order to reset your modem settings instead of a modem power cycle.
Obtaining an IP address - DSL internet
Proceed to the "ENTER Pin" screen on the STB User Interface > "network configurations" > leave the "Automatic" (DHCP) checked > hit apply. If this option corrects the issue you will receive a "DCHP configuration has been set successfully" message. If this does not result in a "DCHP configuration has been set successfully" message proceed to the steps below.
1) Remove the power (power cycle) from the Cable modem and the router if present and leave everything unplugged.
2) Remove the Ethernet cable and power cord from the back of the Fyre Boxxx.
3) Plug in and power on modem and allow it to come back online and then power on the router if present and allow it to reconfigure itself if no router is present, plug in and power on the Fyre Boxxx before proceeding to step 4.
4) Proceed to the "network settings" option on the Enter PIN screen > keep the "automatic (DHCP)" option checked > hit the "apply" button to reconfigure the network settings, if this option corrects the issue you will receive a "DCHP configuration has been set successfully" message. If this does not correct your issue proceed to the "Reconfiguring Your Network Settings - DSL / Cable" section below.
Note: Some modems have a recessed reset or reboot button that will need to be pushed in order to reset the modem configuration settings. The recessed button may not be able to be pushed with your finger and will require a paper clip or pin tip to push the button. If you have a network configuration of modem > box and your attempts to power cycle the network are still not resulting in the box pulling an IP address, you will need to look for the recessed button in order to reset your modem settings instead of a modem power cycle.Reconfiguring Your Network Settings – DSL / Cable
First proceed to the "network settings" option on the Enter PIN screen > keep the "automatic (DHCP)" option checked > hit the "apply" button to reconfigure the network settings, if this option corrects the issue you will receive a "DCHP configuration has been set successfully" message. If this does not result in a "DCHP configuration has been set successfully" message proceed to the following steps.
1) Remove the power (power cycle) from the DSL and or the router if present and leave everything unplugged for 5 seconds
2) Remove the Ethernet cable and power cord from the back of the Fyre Boxxx
3) Plug in the modem and allow it to reconfigure itself (wait for modem to reconfigure before proceeding to step 4 if necessary)
4) Plug in the router if present and allow it to reconfigure itself
5) Plug the Ethernet cable into the back of the Fyre Boxxx
6) Plug the power cord into the back of the Fyre Boxxx, wait 5 seconds and turn on the Fyre Boxxx
7) Proceed to the "network settings" option on the Enter PIN screen > keep the "automatic (DHCP)" option checked > hit the "apply" button to reconfigure the network settings, if this option corrects the issue you will receive a "DCHP configuration has been set successfully" message. If this does not correct the your issue proceed to Tier 2.
Reconfiguring Your Network Settings – DSL / Cable
First proceed to the "network configuration" option on the Enter PIN screen > keep the "automatic (DHCP)" option checked > hit the "apply" button to reconfigure the network settings, if this option corrects the issue you will receive a "DCHP configuration has been set successfully" message. If this does not work proceed to the following steps.
1) Remove the power (power cycle) from the DSL and or the router if present and leave everything unplugged for 5 seconds
2) Remove the Ethernet cable and power cord from the back of the FyreTV Boxxx
3) Plug in the modem and allow it to reconfigure itself (wait for modem to reconfigure before proceeding to step 4 if necessary)
4) Plug in the router if present and allow it to reconfigure itself
5) Plug the Ethernet cable into the back of the Fyre Boxxx
6) Plug the power cord into the back of the FyreTV Boxxx, wait 5 seconds and turn on the FyreTV Boxxx
7) Proceed to the "network configuration" option on the Enter PIN screen > keep the "automatic (DHCP)" option checked > hit the "apply" button to reconfigure the network settings, if this option corrects the issue you will receive a "DCHP configuration has been set successfully" message. If this does correct your issue proceed to reconfigure your
Should you need anything, anything at all, please don’t be shy and reach out to our eagerly awaiting Customer Support.
- Live chat option found on our homepage, www.fyretv.com
- Email support support@fyretv.com
- Customer support hot-line at 888-FYRETV-0 or 888-397-3880 (24 hrs.)
Thank-you, we look forward to servicing you in the future.
FyreTV Team
router settings.
|
No visitor comments posted.
Post a comment
No related articles were found.
No attachments were found.
Print this page
Email this page
Post a comment
Subscribe me
Add to favorites
Remove Highlighting
Edit this Article
